Hochiki CHQ-SZM/M(SCI) Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Audio-Zubehör Hochiki CHQ-SZM/M(SCI) herunter. Hochiki CHQ-SZM/M(SCI) User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 4
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
Hochiki Europe (UK) Ltd
Page 1 2-3-0-778/ISS8/DEC11
CHQ MODULES INSTALLATION INSTRUCTIONS
Products Covered: CHQ SZM (Single Zone Monitor), CHQ-DIM (Dual Input Monitor), CHQ-
DZM (Dual Zone Module)
Introduction
The CHQ "Smart-Fix" Range of Modules consists of the following models:
CHQ-DIM(SCI)
Dual Input Module
CHQ-DZM(SCI))
CHQ-DZM/DIN(SCI)
Dual Zone Monitor
CHQ-DIM/M(SCI)
CHQ-DIM/DIN(SCI)
CHQ-DRC(SCI)
Dual Relay Controller
CHQ-MRC(SCI)
CHQ-MRC/DIN(SCI)
Mains Relay Controller
CHQ-DRC/M(SCI)
CHQ-DRC/DIN(SCI)
CHQ-DSC(SCI)
Dual Sounder Controller
CHQ-SZM(SCI)
Single Zone Monitor
CHQ-DSC/M(SCI) CHQ-SZM/M(SCI)
CHQ-DSC/DIN(SCI) CHQ-SZM/DIN(SCI)
Note: (SCI) indicates Module incorporates a short-circuit isolator. DIN indicates Module housing is designed to fit standard “Top
Hat” DIN Rail.
Components
Standard "Smart-Fix" Modules (including (SCI) versions) are supplied as two individual components (see Fig 1 & 2). DIN versions
are supplied as one unit (see Fig 3).
Fig 1
Fig 2
"Smart-Fix" CHQ Module (Back Plate inc PCB Component)
(Note: configuration of Wiring Terminal blocks differs between models)
CHQ-LID Transparent Module Lid
(Supplied with four screws and acrylic retaining washers)
Setting the Loop Address
The analogue address of the Module is set using the first 7
switches of the 8-bit DIL switch, which in the case of the
Standard CHQ is located through the cut-out section on the top
of the PCB cover. On the DIN version, this switch is located on
the edge of the PCB behind the clear door (see Fig 3).
The switches are numbered 1 to 8 (left to right):
CHQ MODULE
SWITCH UP
ON
SWITCH DOWN
OFF
DIN MODULE
SWITCH UP
OFF
SWITCH DOWN
ON
The switches should be set using a small-tipped screwdriver or
similar.
Refer to the Address Chart (Fig 9) on page 4 for a quick
reference on addresses.
Fig 3
(continued on page 4)
DIN Rail Mountable CHQ Module
Seitenansicht 0
1 2 3 4

Inhaltsverzeichnis

Seite 1 - Setting the Loop Address

Hochiki Europe (UK) Ltd Page 1 2-3-0-778/ISS8/DEC11 CHQ MODULES INSTALLATION INSTRUCTIONS Products Covered: CHQ SZM (Single Zone Monitor), CHQ-DIM (D

Seite 2

Hochiki Europe (UK) Ltd Page 2 2-3-0-778/ISS8/DEC11 CHQ-DIM - DUAL INPUT MONITOR This device is a loop-powered module designed to interface to a va

Seite 3

Hochiki Europe (UK) Ltd Page 3 2-3-0-778/ISS8/DEC11 Standard EOL Options for CHQ-DZM EOL Option Type Part Description OPTION 1 Zener End of line d

Seite 4 - Status LEDs

Hochiki Europe (UK) Ltd Page 4 2-3-0-778/ISS8/DEC11 Installation – "Smart-Fix" Version Set analogue address before installation (see page 1

Kommentare zu diesen Handbüchern

Keine Kommentare